歡迎訪問濟南立強模具有限公司││↟▩!

當前位置▩▩₪◕☁:首頁-新聞中心-公司新聞-塑膠模具開發對材料有什麼要求?

塑膠模具開發對材料有什麼要求?

來源▩▩₪◕☁:http://www.voyagesvietnamcambodge.com/ 日期▩▩₪◕☁:2018-08-08

  具有足夠的表面硬度和耐磨性▩▩₪◕☁:塑膠模具的一般硬度通常在50-60HRC以下↟₪╃▩,熱處理後模具應具有足夠的表面硬度↟₪╃▩,以確保模具具有足夠的剛性◕◕✘│。模具在工作中由於填充和流動的塑膠承受較大的壓縮應力和摩擦↟₪╃▩,要求模具保持其形狀的精度和尺寸精度的穩定性↟₪╃▩,以確保模具具有足夠的使用壽命◕◕✘│。模具耐磨性取決於鋼的化學成分和熱處理硬度↟₪╃▩,因此提高模具的硬度有利於提高其耐磨性◕◕✘│。
    Sufficient surface hardness and wear resistance: the general hardness of plastic molds is usually below 50-60hrc. After heat treatment, the molds shall have sufficient surface hardness to ensure that the molds have sufficient rigidity. Because the filled and flowing plastics bear large compressive stress and friction, the mold is required to maintain the stability of shape accuracy and dimensional accuracy, so as to ensure that the mold has sufficient service life. The wear resistance of die depends on the chemical composition and heat treatment hardness of steel, so improving the hardness of die is helpful to improve its wear resistance.
    優良的機械加工性▩▩₪◕☁:大多數塑膠模具↟₪╃▩,除了EMD加工外需要一定程度的切割和鉗工修理◕◕✘│。為延長切削刀具的使用壽命↟₪╃▩,提高切削效能↟₪╃▩,降低表面粗糙度↟₪╃▩,塑膠模具鋼的硬度必須適當
    山東模具製造廠家
    Excellent machinability: most plastic molds need a certain degree of cutting and fitter repair in addition to EMD processing. In order to prolong the service life of cutting tools, improve cutting performance and reduce surface roughness, the hardness of plastic die steel must be appropriate.
    良好的拋光效能▩▩₪◕☁:優良塑膠製品↟₪╃▩,要求表面粗糙度小◕◕✘│。用於此目的的鋼材需要較少的材料雜質↟₪╃▩,組織細微均勻↟₪╃▩,無纖維方向↟₪╃▩,拋光不應出現點蝕或桔皮樣缺陷◕◕✘│。
    Good polishing performance: excellent plastic products, requiring small surface roughness. The steel used for this purpose needs less material impurities, fine and uniform structure, no fiber direction, and there shall be no pitting or orange peel like defects in polishing.
    良好的熱穩定性▩▩₪◕☁:注塑模具部件的形狀往往比較複雜↟₪╃▩,淬火後難以加工↟₪╃▩,應儘量使用良好的熱穩定性↟₪╃▩,當模具加工熱處理後由於線膨脹係數小↟₪╃▩,熱處理變形小↟₪╃▩,由於尺寸變化率小↟₪╃▩,金相組織和模具尺寸穩定↟₪╃▩,可以減少或不再加工的溫差↟₪╃▩,可以保證模具尺寸精度和表面粗糙度的要求◕◕✘│。
    Good thermal stability: the shape of injection mold parts is often complex and difficult to process after quenching. Good thermal stability should be used as much as possible. After mold processing and heat treatment, due to small linear expansion coefficient and small heat treatment deformation, small size change rate and stable metallographic structure and mold size, the temperature difference can be reduced or no longer processed, It can meet the requirements of die dimensional accuracy and surface roughness.

相關產品 / Related products

濟南立強模具有限公司

魯ICP備15002024號-2

技術支援▩▩₪◕☁:網站建設·推廣運營
網站地圖    TXT    XML
色屋,精品国偷自产在线视频,天天av,丰满的熟妇岳中文字幕