歡迎訪問濟南立強模具有限公司•││·!

當前位置▩•₪:首頁-新聞中心-行業資訊-注塑加工過程中須注意的安全操作細節

注塑加工過程中須注意的安全操作細節

來源▩•₪:http://www.voyagesvietnamcambodge.com/ 日期▩•₪:2022-09-20

注塑成型有一些操作規則╃☁·。我們須知道│₪•·,安全是非常關鍵的╃☁·。今天濟南注塑加工廠家給大家分享並提高我們的安全意識╃☁·。
There are some operation rules for injection molding. We must know that safety is very critical. Today, Jinan injection molding processing factory will share with you and improve our safety awareness.
1.注塑廠始終保持注塑機及其周圍環境整潔╃☁·。注塑機周圍的空間應儘可能保持暢通╃☁·。加入潤滑油或壓力油後│₪•·,應儘快擦淨洩漏的油╃☁·。僅在清理膠桶上的碎屑(例如橡膠顆粒)以避免起火後才能開啟電加熱器╃☁·。如果不需要大修機器或在要時│₪•·,請勿隨意取下熔化器管上的隔熱罩╃☁·。
1. The injection molding plant always keeps the injection molding machine and its surrounding environment clean. The space around the injection molding machine should be kept as smooth as possible. After adding lubricating oil or pressure oil, wipe up the leaked oil as soon as possible. Only turn on the electric heater after cleaning the debris (such as rubber particles) on the rubber bucket to avoid fire. If it is not necessary to overhaul the machine or when necessary, do not remove the heat shield on the melter tube at will.
2.在進行注射處理之前│₪•·,請在操作過程中檢查是否可以透過按下緊急按鈕或開啟安全門來終止夾緊╃☁·。
2. Before injection, please check whether clamping can be terminated by pressing the emergency button or opening the safety door during operation.
3.向前移動射擊臺時│₪•·,請勿用手除去從噴嘴洩漏的深層膠水│₪•·,以免將手捏在射擊臺和模具之間│₪•·,並造成物理損壞╃☁·。清潔機筒時│₪•·,將噴嘴溫度調節至合適的較高溫度│₪•·,以保持噴嘴暢通無阻│₪•·,然後使用低的注射壓力和速度除去機筒中殘留的橡膠╃☁·。在清潔過程中│₪•·,請勿直接用手觸控它╃☁·。剛被射擊的橡膠混合物│₪•·,以免被燃燒╃☁·。
3. When moving the shooting table forward, please do not remove the deep glue leaked from the nozzle with your hands to avoid pinching your hands between the shooting table and the mold and causing physical damage. When cleaning the barrel, adjust the nozzle temperature to a suitable higher temperature to keep the nozzle unblocked, and then use low injection pressure and speed to remove the residual rubber in the barrel. Do not touch it directly with your hands during cleaning. Rubber mixture just shot to avoid burning.
4.避免將熱敏性和腐蝕性塑膠在桶中放置太長時間│₪•·,並嚴格遵循塑膠供應商提供的關機和清潔方法╃☁·。更換塑膠時│₪•·,請確保新舊塑膠的混合不會產生化學反應│₪•·,否則須使用其他塑膠去除機筒中的殘留材料╃☁·。
4. Avoid placing heat sensitive and corrosive plastics in the barrel for too long, and strictly follow the shutdown and cleaning methods provided by the plastic supplier. When replacing plastics, please ensure that the mixing of new and old plastics will not produce chemical reaction, otherwise other plastics must be used to remove the residual materials in the barrel.
濟南注塑加工
5.請勿取消安全門或安全開關以提高生產速度╃☁·。注塑之前│₪•·,請檢查模具是否牢固地安裝在注塑機的可移動模板和頂板上╃☁·。注意注塑機的地線和其他接線是否正確連線╃☁·。
5. Do not cancel the safety door or safety switch to improve the production speed. Before injection molding, please check whether the mold is firmly installed on the movable template and top plate of the injection molding machine. Pay attention to whether the ground wire and other wiring of the injection molding machine are correctly connected.
6.安裝模具時│₪•·,須先將起重環完全擰入模具起重孔中│₪•·,然後再起吊╃☁·。安裝模具後│₪•·,應根據模具尺寸調整注塑機安全杆的長度│₪•·,以便在開啟安全門時│₪•·,機器安全擋塊(機械鎖)可以停止注塑從鎖定的機器╃☁·。
6. When installing the mold, the lifting ring must be completely screwed into the mold lifting hole before lifting. After installing the mold, adjust the length of the safety bar of the injection molding machine according to the mold size, so that when the safety door is opened, the machine safety stop (mechanical lock) can stop injection molding from the locked machine.
7.在正常注塑過程中│₪•·,嚴禁操作員在未開啟安全門的情況下從注塑機上方或下方取出注塑件╃☁·。檢查模具或暫時不生產時│₪•·,應及時關閉注塑機的油泵電機╃☁·。
7. During the normal injection molding process, it is strictly forbidden for the operator to take out the injection molding parts from above or below the injection molding machine without opening the safety door. When checking the mold or temporarily stopping production, the oil pump motor of the injection molding machine should be turned off in time.
8.在注塑過程中│₪•·,一個人可以操作│₪•·,不允許多人同時操作╃☁·。禁止操作控制面板│₪•·,而另一個則同時調節模具或執行其他操作╃☁·。
8. In the injection molding process, one person can operate, and multiple persons are not allowed to operate at the same time. It is prohibited to operate the control panel, while the other one adjusts the mold or performs other operations at the same time.
以上就是濟南注塑加工廠家給大家分享的文章│₪•·,希望對大家有所幫助╃☁·。更多注意事項就來我們網站http://www.voyagesvietnamcambodge.com諮詢吧•││·!
The above is the article that Jinan injection molding processing factory shared with you, hoping to help you. More notes on our website http://www.voyagesvietnamcambodge.com Consult!

相關產品 / Related products

濟南立強模具有限公司

魯ICP備15002024號-2

技術支援▩•₪:網站建設·推廣運營
網站地圖    TXT    XML
色屋,精品国偷自产在线视频,天天av,丰满的熟妇岳中文字幕